01 The meaning of draft angle Structural design of plastic parts: draft angle Draft angle, as you can tell from the literal meaning, is the angle designed for the mold. To be precise, it is the mold ejection angle of the surface of the molding part in the direction parallel to the mold ejection direction, […]
Structural design of plastic parts: draft angle Read More »
The most commonly used chamfers are divided intoRoundandchamferRounding refers to connecting two curved surfaces of a part tangently through a rounded surface. A standard rounded corner usually uses a radius value R to represent its size. Structural design of plastic parts: chamfering Chamfering refers to connecting two curved surfaces of a part at an angle
Structural design of plastic parts: chamfering Read More »
Injection molding machine production generally operates 24 hours a day. For machines that are in working condition for a long time, we must do a good job in maintenance and strive to find and solve problems before the machine breaks down. Otherwise, once the machine fails, production must be stopped and repaired, affecting production. Therefore,
Do you know how to design a plastic part embedded in a nut If: there is no problem in the selection of plastic and nut, the standard state of the nut after being embedded in the plastic is shown in Figure (I)If: the nut size is too small, the plastic BOSS hole is too large,
Do you know how to design a plastic part embedded in a nut? Read More »
Program control of injection speed The program control of the injection speed is to divide the injection stroke of the screw into 3 to 4 stages, and use the appropriate injection speed in each stage. For example: slow down the injection speed when the molten plastic first passes through the gate, use high-speed injection during
Condition Control Instructions In The Injection Molding Process Read More »
PE is a crystalline raw material with very little hygroscopicity, no more than 0.01%, so there is no need for drying before processing. PE molecular chains have good flexibility, small forces between bonds, low melt viscosity, and excellent fluidity. Therefore, thin-walled long-flow products can be formed without too high pressure during molding. The shrinkage range
Injection molding process of polyethylene PE Read More »
The working conditions of plastic molds are different from those of cold stamping dies. They generally have to work at 150 degrees Celsius to 200 degrees Celsius. In addition to being subject to a certain pressure, they also have to withstand the influence of temperature. According to the different usage conditions and processing methods of
Selection tips for plastic mold materials Read More »
Pre-molding action selection Depending on whether the injection seat retreats before and after pre-plastic feeding, that is, whether the nozzle leaves the mold, the injection molding machine generally has three options: Fixed feeding: the nozzle is always attached to the mold before and after pre-molding, and the injection seat does not move. Front feeding: The
Injection Molding Pre-molding Action And Back Pressure Control Read More »
Two-color injection molding technology is also called double-material injection molding technology. This is a technology that uses two plastic materials to be mixed and injection molded to form plastic products. Its technical connotation is actually to use a mold component to shape the shape and mold it in the mold. Welding work, so the basic
Introduction to two-color injection molding technology and mold characteristics Read More »
​ When the mold temperature is not high, resins whose material fluidity deteriorates significantly, such as polycarbonate PC, polyphenylene ether PPO, polyethylene terephthalate, commonly known as polyester resin PETP, etc., require the mold temperature to be heated to 80 degree or above (use a mold temperature regulator). ​​
Reasons and solutions for shortage of plastic products Read More »
Plastic gear parts injection molding process and material analysis. Plastic gears are developing toward larger sizes, more complex geometries, and higher strength, with high-performance resins and long-glass fiber-filled composites playing an important role. Plastic gears have experienced a change from new materials to important industrial materials in the past 50 years. Today they have penetrated
Plastic gear parts injection molding process and material analysis Read More »
In order to strengthen the hardness of the metal surface, many manufacturers will use the quenching process to promote the production of moulds, and the cracks generated after the quenching of the moulds are a defect in the heat treatment process *, which is likely to cause the processed moulds to be scrapped. What are
What are the factors that cause cracks during mould quenching Read More »
