Company

How To Solve The Problem Of Defects In The Gate Area Of Injection Mould Products?

We have defects in the gate area during the process of injection mould. What is the reason for this phenomenon? Is there any good way to solve it? Causes Of Light Line In Injection Mould In the point gate design perpendicular to the direction of the part, a radiation system consisting of different color depths and glosses centered on the gate appears on the surface of the part during injection molding, called a ray of light.  There are generally three manifestations, namely dark lines with dark background, dark lines with dark background and dense and white dark lines around the gate. Such defects mostly occur when injecting polystyrene and modified polystyrene mixtures, and are related to the following factors: the two materials have differences in rheology, colorability, etc., and the flow rates of the stratosphere and turbulent layer of the pouring system.  There are differences in heating conditions; plastics produce burnt wires due to thermal decomposition; gaseous substances interfere with the plastics when entering the mold. https://www.sciencedirect.com/science/article/abs/pii/S0263436823002123 Injection Mould Light Line Solution Causes Of Cold Spots In Injection Mould Cold spots mainly refer to the foggy or brightcolored spots near the gate of the part or the curved scars starting from the gate that look like earthworms sticking to it.  They are caused by the plastic front entering the cavity or due to excessive pressure holding. It is caused by the cold material that is later squeezed into the mold cavity. The front material transfers heat due to the cooling effect of the nozzle or runner, and is partially cooled and solidified before entering the mold cavity. When it expands through the narrow gate and is injected into the mold cavity, the melt ruptures, and is then heated by the subsequent heat. The molten material pushes around and becomes a cold material spot. Solution To Cold Spots In Injection Mould Contact Person: Alex ChuWhatsApp/ WeChat: 0086 18968677763Email: sc10@solidcomould.comWebsite: www.solidcomould.com

How To Solve The Problem Of Defects In The Gate Area Of Injection Mould Products? Read More »

How To Make Injection Molded Products With Good Transparency?

There are many standards to measure the transparency of some injection molded products, including transmittance, haze, refractive index, birefringence and dispersion. See whether the hardness and strength of the material are required. Transparent injection molding products generally use PS, SNA (AS) materials, PMMA and other materials, but they all have a brittle problem that needs

How To Make Injection Molded Products With Good Transparency? Read More »

School Table Mould School Table Mold Maintenance Plan

1. Inspection and maintenance of the school table mould school table mold when loading the mould 2. School table mould maintenance in the production table Observe frequently and feel the status of the school table mold during production. If any abnormalities are found, stop the machine immediately for inspection and eliminate them in time. Start production

School Table Mould School Table Mold Maintenance Plan Read More »

Nine common problems of color masterbatch

This problem needs to be considered from two aspects of plastic physical and mechanical properties and plastic molding process: Nine common problems of color masterbatch Influence of physical and mechanical properties of plastics:https://solidcomould.com/product/2-cavity-plastic-flower-pot-mould/ This may be due to poor diffusion and mutual solubility caused by the poor quality of the dispersant or additives selected by

Nine common problems of color masterbatch Read More »

Injection mold maintenance specifications in three cases

Maintenance purpose: To ensure the normal production of the mold, reduce faults and quality problems, and prolong the service life of the mold.Maintenance before, during and after the production of the mold, maintenance items and precautions:Mold maintenance before production:Scrub the dust, oil and rust on the surface of the mold, remove the dirt on the

Injection mold maintenance specifications in three cases Read More »

Introduction of injection molding process that affects the strength of injection molded parts at three points

Injection molding is a method of producing shapes for industrial products. Products usually use rubber injection molding and plastic injection molding. Injection molding can also be divided into injection molding molding method and die casting method. Introduction of injection molding process that affects the strength of injection molded parts at three points Injection molding machine

Introduction of injection molding process that affects the strength of injection molded parts at three points Read More »

Some Knowledge About Exhaust Groove In Plastic Moulds

1. Why do you need to open the exhaust groove During the injection molding process, when the molten plastic enters the mold cavity, the air in the cavity needs to be exhausted instantly, including the air existing in the cavity and the gating system, and the water produced by the evaporation of moisture contained in the

Some Knowledge About Exhaust Groove In Plastic Moulds Read More »

Playground Slide Large Injection Mold Design And 3D

https://solidcomould.com/product-category/injection-mould/ The maximum dimensions of the playground slide product are 1438.89 mm x 376.95 mm x 214.80 mm, the average thickness of the plastic part is 3.17 mm, the material of the plastic part is PE, the shrinkage rate is 1.018, and the weight of the plastic part is 2726.03 grams. The technical requirements for plastic parts are that there should be no defects such as peaking, injection dissatisfaction, flow lines, pores, warping deformation, silver streaks, cold material, and spray lines. Playground slides are common entertainment facilities in kindergartens. There are various structures of slides, including ups and downs, slides down slopes, and spiral rotations. Playground slides are commonly designed and manufactured with materials such as PE and PP. Safety needs to be paid attention to when designing the product. The material itself is

Playground Slide Large Injection Mold Design And 3D Read More »

Scroll to Top